|
The pictorials are illustrated with spaces between beads for a clearer direction, in the actual beading, there should be no spaces.
|
|
Go back to page 1 of the full tutorial!
Always Remember to pull tight on EVERY STEP.
|
|
|
| Step 21: |
- Continue to:
Add two red beads on the top left (blue) string, crisscross the bottom right (black) string through the last bead added.
Continue to pass the blue string (the one you just used to add new beads on) through one old bead from step 12 (marked A).
|
|
 |
| Step 22: |
- Continue to:
Add one white bead on one of the string, crisscross the other string through this new bead added.
|
|
|
| Step 23: |
- Continue to:
Add two white beads on the left (blue) string, crisscross the right (black) string through the last bead added.
Continue to pass the blue string (the one you just used to add new beads on) through one old crystal from step 13 (marked A).
|
|
 |
| Step 24: |
- Continue to:
Add one white bead on one of the string, crisscross the other string through this new bead added.
|
|
 |
| Step 25: |
- Continue to:
Add two white beads on the bottom (blue) string, crisscross the top (black) string through the last bead added.
Continue to pass the blue string (the one you just used to add new beads on) through one old crystal from step 14 (marked A).
|
|
 |
| Step 26: |
- Continue to:
Add one white bead on the bottom (black) string, crisscross the top (blue) string through this bead added.
Continue to pass the black string (the one you just used to add new beads on) through one old bead from step 16 (marked A).
|
|
 |
| Step 27: |
- Continue to:
Add one red bead on one of the string, crisscross the other string through this new bead added.
|
|
 |
| Step A: |
- Place your beading aside for a while and make this piece with the eye pin and 3mm or 4mm bead.
1. Place one 3mm or 4mm bead (depending which one
fits best into your base of the beaded piece you
have made so far) two seed beads
2. Now place your beadwork through you have done so
far wider end down into the eye pin too.
3. Cut away excess eye pin wire leaving only about
1cm. Bent the eye pin wire that's left with a flat tip
pliers into a 90 degree angle.
4. Use a round tip pliers, curl the eye pin wire from tip
inwards to make a round closed loop.
|
|
|
|
 |
| Step 28: |
- Continue from step 27:
Add three red beads on the bottom (black) string, crisscross the top (blue) string through the last bead added.
Continue to pass the black string (the one you just used to add new bead on) through one old bead from step 17 (marked A).
|
|
 |
| Step 29: |
- Continue to:
Add two red beads on the bottom right (blue) string, crisscross the top left (black) string through the last bead added.
Continue to pass the blue string (the one you just used to add new bead on) through one old bead from step 19 (marked A).
|
|
 |
| Step 30: |
- Continue to:
Add two red beads on the top right (black) string, crisscross the bottom left (blue) string through the last bead added.
Continue to pass the black string (the one you just used to add new bead on) through one old bead from step 21 (marked A).
|
|
 |
| Step 31: |
- Continue to:
Add two red beads on the top (blue) string, crisscross the bottom (black) string through the last bead added.
Continue to pass the blue string (the one you just used to add new bead on) through one old bead from step 23 (marked A).
|
|
 |
| Step 32: |
- Continue to:
Add one red and one white beads on the top right (black) string, crisscross the bottom left (blue) string through the last bead added.
Continue to pass the black string (the one you just used to add new bead on) through two old beads from step 25 and 28 (marked A
and B).
|
|
 |
| Step 33: |
- Continue to:
Add one red bead on one of the string, crisscross the other string through this new bead added.
|
|
 |
| Step 34: |
- Continue to:
Pass one side of the string that's longer than the other (Mine is the right (blue) string) back up though five old beads marked A,
B, C,
D and E, from steps 28, 29, 30, 31 and 32.
Tie off when the two strings meet head to head and pass the excess strings back through the piece to hide the ends.
|
|
 |
